کابل سیسکو 530Mt قابلیت اتصال یک پورت سریال از مودم خط لیز مخابراتی یا غیره را به پورت سریال روتر ما که اغلب کارت Wic1T می باشد را فراهم مینماید. که در برخی روتر ها همچون 1601 این کارت احتیاج نمی باشد و کابل مستقیم به پورت سریال بر روی خود روتر متصل می گردد.
This document explains the V.35 serial cable assembly and pinouts.
There are no specific requirements for this document.
This document is not restricted to specific software and hardware versions.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
For more information on document conventions, refer to the Cisco Technical Tips Conventions.
The table here lists the different V.35 speed and distance limitations:
 Caution: The EIA,TIA-449 and V.35 interfaces support data rates up to 2.048 Mbps. Cisco advices not to exceed this maximum as it could result in loss of data.
|
Data Rate (Baud) |
Distance (Feet) |
Distance (Meters) |
|
2400 |
4,100 |
1,250 |
|
4800 |
2,050 |
625 |
|
9600 |
1,025 |
312 |
|
19200 |
513 |
156 |
|
38400 |
256 |
78 |
|
56000 |
102 |
31 |
|
T1 |
50 |
15 |
The cable gender for this product (part number 72-0791-01) is male DB-60 to male Winchester 15 Pin, mode - DTE.
The CAB-V35MT serial cable is used in the Cisco 7000 family, Cisco 4000 series, Cisco 3600 series, Cisco 2500 series, Cisco 1600 series, Cisco access servers, and AccessPro PC cards. This cable has a male DB-60 connector on the Cisco end and a male Winchester connector on the network end.
The table here shows the V.35 DTE cable pinouts (DB-60 to 34-Pin).
Note: The arrows indicate signal direction:
|
60 Pin1 |
Signal |
Description |
Direction |
34 Pin |
Signal |
|
J1-49
J1-48 |
MODE_1
GND |
Shorting Group |
-- |
-- |
-- |
|
J1-50
J1-51
J1-52 |
MODE_0
GND
MODE_DCE |
Shorting Group |
-- |
-- |
-- |
|
J1-53
J1-54
J1-55
J1-56 |
TxC/NIL
RxC_TxCE
RxD/TxD
GND |
Shorting Group |
-- |
-- |
-- |
|
J1-46 |
Shield_GND |
Single |
-- |
J2-A |
Frame GND |
|
J1-45
Shield |
Circuit_GND
-- |
Twisted pair no. 12 |
--
-- |
J2-B
Shield |
Circuit_GND
-- |
|
J1-42
Shield |
RTS/CTS
-- |
Twisted pair no. 9 |
-->
-- |
J2-C
Shield |
RTS
-- |
|
J1-35
Shield |
CTS/RTS
-- |
Twisted pair no. 8 |
<--
-- |
J2-D
Shield |
CTS
-- |
|
J1-34
Shield |
DSR/DTR
-- |
Twisted pair no. 7 |
<--
-- |
J2-E
Shield |
DSR
-- |
|
J1-33
Shield |
DCD/LL
-- |
Twisted pair no.6 |
<--
-- |
J2-F
Shield |
RLSD
-- |
|
J1-43
Shield |
DTR/DSR
-- |
Twisted pair no. 10 |
-->
-- |
J2-H
Shield |
DTR
-- |
|
J1-44
Shield |
LL/DCD
-- |
Twisted pair no. 11 |
-->
-- |
J2-K
Shield |
LT
-- |
|
J1-18
J1-17 |
TxD/RxD+
TxD/RxD-- |
Twisted pair no. 1 |
-->
--> |
J2-P
J2-S |
SD+
SD-- |
|
J1-28
J1-27 |
RxD/TxD+
RxD/TxD-- |
Twisted pair no. 5 |
<--
<-- |
J2-R
J2-T |
RD+
RD-- |
|
J1-20
J1-19 |
TxCE/TxC+
TxCE/TxC-- |
Twisted pair no. 2 |
-->
--> |
J2-U
J2-W |
SCTE+
SCTE-- |
|
J1-26
J1-25 |
RxC/TxCE+
RxC/TxCE-- |
Twisted pair no. 4 |
<--
<-- |
J2-V
J2-X |
SCR+
SCR-- |
|
J1-24
J1-23 |
TxC/RxC+
TxC/RxC-- |
Twisted pair no. 3 |
<--
<-- |
J2-Y
J2-AA |
SCT+
SCT-- |
1Any pin not referenced is not connected.
The cable gender for this product (part number 72-0792-01) is male DB-60 to female Winchester Block Type, mode - DCE.
The CAB-V35FC serial cable is used in the Cisco 7000 family, Cisco 4000 series, Cisco 3600 series, Cisco 2500 series, Cisco 1600 series, Cisco access servers, and AccessPro PC cards. This cable has a male DB-60 connector on the Cisco end and a female Winchester connector on the network end.
The table here shows the V.35 DCE cable pinouts (DB-60 to 34-Pin).
Note: The arrows indicate signal direction:
|
60 Pin1 |
Signal |
Description |
Direction |
34 Pin |
Signal |
|
J1-49
J1-48 |
MODE_1
GND |
Shorting Group |
-- |
-- |
-- |
|
J1-50
J1-51 |
MODE_0
GND |
Shorting Group |
-- |
-- |
-- |
|
J1-53
J1-54
J1-55
J1-56 |
TxC/NIL
RxC_TxCE
RxD/TxD
GND |
Shorting Group |
-- |
-- |
-- |
|
J1-46 |
Shield_GND |
Single |
-- |
J2-A |
Frame GND |
|
J1-45
Shield |
Circuit_GND
-- |
Twisted pair no. 12 |
--
-- |
J2-B
Shield |
Circuit_GND
-- |
|
J1-35
Shield |
CTS/RTS
-- |
Twisted pair no. 8 |
<--
-- |
J2-C
Shield |
RTS
-- |
|
J1-42
Shield |
RTS/CTS
-- |
Twisted pair no. 9 |
-->
-- |
J2-D
Shield |
CTS
-- |
|
J1-43
Shield |
DTR/DSR
-- |
Twisted pair no. 10 |
-->
-- |
J2-E
Shield |
DSR
-- |
|
J1-44
Shield |
LL/DCD
-- |
Twisted pair no. 11 |
-->
-- |
J2-F
Shield |
RLSD
-- |
|
J1-34
Shield |
DSR/DTR
-- |
Twisted pair no.7 |
<--
-- |
J2-H
Shield |
DTR
-- |
|
J1-33
Shield |
DCD/LL
-- |
Twisted pair no. 6 |
<--
-- |
J2-K
Shield |
LT
-- |
|
J1-28
J1-27 |
RxD/TxD+
RxD/TxD-- |
Twisted pair no. 5 |
<--
<-- |
J2-P
J2-S |
SD+
SD-- |
|
J1-18
J1-17 |
TxD/RxD+
TxD/RxD-- |
Twisted pair no. 1 |
-->
--> |
J2-R
J2-T |
RD+
RD-- |
|
J1-26
J1-25 |
RxC/TxCE+
RxC/TxCE-- |
Twisted pair no. 4 |
<--
<-- |
J2-U
J2-W |
SCTE+
SCTE-- |
|
J1-22
J1-21 |
NIL/RxC+
NIL/RxC-- |
Twisted pair no. 3 |
-->
--> |
J2-V
J2-X |
SCR+
SCR-- |
|
J1-20
J1-19 |
TxCE/TxC+
TxCE/TxC-- |
Twisted pair no. 2 |
-->
--> |
J2-Y
J2-AA |
SCT+
SCT-- |
1Any pin that is not referenced is not connected.
|
Home
Cisco Router
Special Device
